VGLA Lite Slave is a Connect IQ data field for Edge 130/130 Plus. Combine metrics in one field and record virtual gear tooth-count candidates in FIT. Choose 4/6/8 cells or Power Graph + 2 Cells. Assign each cell; text size/labels adapt to the field area. Use full-screen or beside VGLA Lite PD Analysis/PCH Alert Lite in a two-field layout. Metrics depend on data received by Edge. [130 Edition VGLA Configurator] https://toabcycling.org/VGLA_Configurator_130.html Free Japanese/English browser editor for all 29 settings: Normal/Workout pages, metrics, FTP, graph, drivetrain and HR/cadence inversion. Includes previews and JSON backup. Apply settings: 1. Edit, generate and copy the complete VGLS6 code. 2. Paste into Slave's "Receive Settings Code" in Garmin Connect Mobile; save and sync. 3. Display Slave on Edge. 4. Reopen mobile settings and check "Receive Result" for "Applied: settings". Mobile settings: code input/result only. Edit in Configurator. To reapply, clear/save/sync first. Invalid codes keep settings. Keep JSON backups. VGLS1-5 supported. Device/mobile labels: English. Regular VGLA codes are incompatible. [Display and Workouts] Normal/Workout layouts and metrics are independent. 130 Plus can auto-switch on workout detection and show NOW/NEXT target power. Auto Remaining follows time/distance end conditions and holds during pauses. Other conditions/unavailable data show "--". FTP-based targets require FTP. [Virtual Gears and FIT Recording] Using configured chainrings, cassette, wheel circumference and Edge Speed/Cadence, Slave calculates inner/outer rear-tooth candidates. GEAR I/O shows both; single-side displays and single chainrings are supported. A FIT Developer Field stores front teeth and both rear candidates regardless of display selection. Stops, coasting, missing data, speed below 5.4 km/h or cadence below 20 rpm invalidate rear candidates; old values are not retained. Parallel hypotheses do not confirm front selection or shift events. Recording intervals depend on Edge's FIT mode. [Power and Graph] Edge-native power feeds 30s Average Power, Normalized Power (NP), Intensity Factor (IF), Training Stress Score (TSS) and Work (kJ). FTP=0 disables IF/TSS; 30s Power/NP/Work do not require FTP. 30s Power/NP/IF/TSS show "--" until the initial 30-second window is ready. Accumulation pauses with the activity timer and clears on activity reset. The graph shows about two minutes, with 3s/10s averaging and a 100-1000 W maximum. [HR/Cadence Inversion] Current HR cells invert at/above the upper threshold. Cadence uses a low threshold/range: 80/20 inverts 61-80 rpm, excluding 60 or below and zero. Threshold=0 disables inversion. Averages are unaffected. [Other Metrics] Clock, activity/elapsed/lap timers, activity/lap distance, current/average speed, HR, cadence and power; grade, altitude, ascent, Edge battery and Off. [Cycling Data Analyzer] https://toabcycling.org/analyzer/analyzer.html Review FIT gear candidates in the free compatible Analyzer; assign inner/outer intervals or explicitly run estimation. TOAB Cycling CONNECT IQ APPS https://toabcycling.org/ [Getting Started] Add Slave to your profile's data screen, apply its code, connect sensors to Edge and start recording. [Compatibility and Data] Uses Edge-native data. PD Analysis does not share directly received Power/Cadence. Without Edge-native power, power metrics/graph are unavailable. Gears need Edge Speed/Cadence. NP/IF/TSS/30s Power/Work are not added as Developer Fields. Power calculations may differ from Garmin or other services. Gear candidates may differ from actual gears; not every shift is guaranteed to be recorded. Prioritize road safety and traffic rules. Editing/analysis run in-browser. No settings, FITs, ride data or results are sent to VGLA servers. Online maps use external map services. [Devices] Edge 130/130 Plus. Workouts: 130 Plus only. Minimum Connect IQ API: 3.1.0.

Release Notes v0.1.17 - Added virtual gear displays: GEAR I/O, Inner Rear Teeth and Outer Rear Teeth. - Added gear candidate calculations based on configured chainrings, cassette and wheel circumference. - Added support for single-chainring setups. - Added FIT Developer Field recording of front tooth counts and rear-tooth candidates for both inner and outer chainrings. - Gear candidates are recorded even when no gear display cell is selected. - Improved candidate invalidation during stops, coasting, missing data and low-speed conditions to prevent stale gear candidates. - Added cell inversion when current heart rate reaches the configured upper threshold. - Added cell inversion for current cadence using a configurable low threshold and inversion range. - Unified workout remaining-time/distance displays into Auto Remaining, which follows each step's end condition. - Added automatic migration of saved legacy workout remaining-time/distance cells to Auto Remaining. - Simplified mobile settings to two fields: Receive Settings Code and Receive Result. All 29 settings are now edited in the 130 Edition Configurator. - Fixed an issue where default display items remained unchanged despite an "Applied: settings" result. - Improved settings retention after saving, syncing and restarting. - Improved memory management during settings reception, reloading and app shutdown. - Preserved compatibility with existing saved settings and VGLS1-6 settings codes. - Retained the production Application ID while incorporating Beta v0.1.20 features. Notes: - Virtual gears are tooth-count candidates calculated under separate inner/outer chainring assumptions. They do not identify the actual front-chainring selection or confirmed shift events. - Gear display and recording require Edge-native Speed/Cadence. Recording intervals depend on the device's FIT recording mode. - Workout features are supported only on Edge 130 Plus. - Power displays and the graph require Edge-native power. Data is not shared between Slave and PD Analysis. - Use a version of Cycling Data Analyzer that supports production Slave recordings. v0.1.11 - Added a “Power Graph + 2 Cells” layout, with the graph on top and two numeric cells below. - Added selectable 3-second and 10-second averaging for the power graph. - Added a configurable power graph maximum and an FTP reference line. - Added a dedicated workout page alongside the normal page. - Added independent layout and display item settings for each page. - Added automatic switching to the workout page when a workout is detected, and return to the normal page when it ends. - Added display items for current and next step target power, step time remaining, and step distance remaining. - Added handling to preserve workout time remaining and page state while activity recording is paused. - Added full support for receiving and applying settings codes generated by the Configurator. - Placed “Receive Settings Code” and “Receive Result” at the top level of the settings menu, and grouped existing options under “Individual Settings / Advanced.” - Added invalid code rejection, settings recovery after failed or interrupted saves, and protection against reapplying the same code over subsequent individual edits. - Reduced memory usage to address IQ! errors observed after saving settings codes. - Maintained compatibility with existing display items, saved cell configurations, and older settings code formats. - Incorporated the latest beta features while retaining the existing production Application ID. Note: Workout detection and display are supported on Edge 130 Plus only, not the original Edge 130. Note: The power graph requires Edge’s standard power data and cannot be displayed when used with PD Analysis. v0.1.6 ・Added 30-second Average Power ・Added Normalized Power (NP) ・Added Intensity Factor (IF) ・Added Training Stress Score (TSS) ・Added Work (kJ) ・Added an FTP setting for IF and TSS calculations ・Setting FTP to 0 now disabl