VGLA Lite Slave is a Connect IQ data field for Edge 130/130 Plus. Combine metrics in one field and record virtual gear tooth-count candidates in FIT. Choose 4/6/8 cells or Power Graph + 2 Cells. Assign each cell; text size/labels adapt to the field area. Use full-screen or beside VGLA Lite PD Analysis/PCH Alert Lite in a two-field layout. Metrics depend on data received by Edge. [130 Edition VGLA Configurator] https://toabcycling.org/VGLA_Configurator_130.html Free Japanese/English browser editor for all 29 settings: Normal/Workout pages, metrics, FTP, graph, drivetrain and HR/cadence inversion. Includes previews and JSON backup. Apply settings: 1. Edit, generate and copy the complete VGLS6 code. 2. Paste into Slave's "Receive Settings Code" in Garmin Connect Mobile; save and sync. 3. Display Slave on Edge. 4. Reopen mobile settings and check "Receive Result" for "Applied: settings". Mobile settings: code input/result only. Edit in Configurator. To reapply, clear/save/sync first. Invalid codes keep settings. Keep JSON backups. VGLS1-5 supported. Device/mobile labels: English. Regular VGLA codes are incompatible. [Display and Workouts] Normal/Workout layouts and metrics are independent. 130 Plus can auto-switch on workout detection and show NOW/NEXT target power. Auto Remaining follows time/distance end conditions and holds during pauses. Other conditions/unavailable data show "--". FTP-based targets require FTP. [Virtual Gears and FIT Recording] Using configured chainrings, cassette, wheel circumference and Edge Speed/Cadence, Slave calculates inner/outer rear-tooth candidates. GEAR I/O shows both; single-side displays and single chainrings are supported. A FIT Developer Field stores front teeth and both rear candidates regardless of display selection. Stops, coasting, missing data, speed below 5.4 km/h or cadence below 20 rpm invalidate rear candidates; old values are not retained. Parallel hypotheses do not confirm front selection or shift events. Recording intervals depend on Edge's FIT mode. [Power and Graph] Edge-native power feeds 30s Average Power, Normalized Power (NP), Intensity Factor (IF), Training Stress Score (TSS) and Work (kJ). FTP=0 disables IF/TSS; 30s Power/NP/Work do not require FTP. 30s Power/NP/IF/TSS show "--" until the initial 30-second window is ready. Accumulation pauses with the activity timer and clears on activity reset. The graph shows about two minutes, with 3s/10s averaging and a 100-1000 W maximum. [HR/Cadence Inversion] Current HR cells invert at/above the upper threshold. Cadence uses a low threshold/range: 80/20 inverts 61-80 rpm, excluding 60 or below and zero. Threshold=0 disables inversion. Averages are unaffected. [Other Metrics] Clock, activity/elapsed/lap timers, activity/lap distance, current/average speed, HR, cadence and power; grade, altitude, ascent, Edge battery and Off. [Cycling Data Analyzer] https://toabcycling.org/analyzer/analyzer.html Review FIT gear candidates in the free compatible Analyzer; assign inner/outer intervals or explicitly run estimation. TOAB Cycling CONNECT IQ APPS https://toabcycling.org/ [Getting Started] Add Slave to your profile's data screen, apply its code, connect sensors to Edge and start recording. [Compatibility and Data] Uses Edge-native data. PD Analysis does not share directly received Power/Cadence. Without Edge-native power, power metrics/graph are unavailable. Gears need Edge Speed/Cadence. NP/IF/TSS/30s Power/Work are not added as Developer Fields. Power calculations may differ from Garmin or other services. Gear candidates may differ from actual gears; not every shift is guaranteed to be recorded. Prioritize road safety and traffic rules. Editing/analysis run in-browser. No settings, FITs, ride data or results are sent to VGLA servers. Online maps use external map services. [Devices] Edge 130/130 Plus. Workouts: 130 Plus only. Minimum Connect IQ API: 3.1.0.

Release Notes v0.1.18 - Added “1 Graph + 4 Cells” while retaining “1 Graph + 2 Cells.” - Made the new layout available on both normal and workout pages. - Added left-aligned labels and right-aligned values to Graph + 4 Cells, 6-cell and 8-cell layouts when placed in screens with two or more data fields. - Improved the 6-cell layout in a two-field screen to retain the numeric font size used by the 4-cell layout. - Applied the same font-size preservation to Graph + 4 Cells and 8-cell layouts where space allows. - Standardized inline labels to a smaller font. Labels are hidden when they cannot fit beside the values. - Preserved existing full-screen, 4-cell and Graph + 2 Cells displays. - Reduced memory usage when saving settings and improved stability. - Maintained compatibility with saved settings, older settings codes and gear-candidate FIT recording. v0.1.17 - Added virtual gear displays: GEAR I/O, Inner Rear Teeth and Outer Rear Teeth. - Added gear candidate calculations based on configured chainrings, cassette and wheel circumference. - Added support for single-chainring setups. - Added FIT Developer Field recording of front tooth counts and rear-tooth candidates for both inner and outer chainrings. - Gear candidates are recorded even when no gear display cell is selected. - Improved candidate invalidation during stops, coasting, missing data and low-speed conditions to prevent stale gear candidates. - Added cell inversion when current heart rate reaches the configured upper threshold. - Added cell inversion for current cadence using a configurable low threshold and inversion range. - Unified workout remaining-time/distance displays into Auto Remaining, which follows each step's end condition. - Added automatic migration of saved legacy workout remaining-time/distance cells to Auto Remaining. - Simplified mobile settings to two fields: Receive Settings Code and Receive Result. All 29 settings are now edited in the 130 Edition Configurator. - Fixed an issue where default display items remained unchanged despite an "Applied: settings" result. - Improved settings retention after saving, syncing and restarting. - Improved memory management during settings reception, reloading and app shutdown. - Preserved compatibility with existing saved settings and VGLS1-6 settings codes. - Retained the production Application ID while incorporating Beta v0.1.20 features. Notes: - Virtual gears are tooth-count candidates calculated under separate inner/outer chainring assumptions. They do not identify the actual front-chainring selection or confirmed shift events. - Gear display and recording require Edge-native Speed/Cadence. Recording intervals depend on the device's FIT recording mode. - Workout features are supported only on Edge 130 Plus. - Power displays and the graph require Edge-native power. Data is not shared between Slave and PD Analysis. - Use a version of Cycling Data Analyzer that supports production Slave recordings. v0.1.11 - Added a “Power Graph + 2 Cells” layout, with the graph on top and two numeric cells below. - Added selectable 3-second and 10-second averaging for the power graph. - Added a configurable power graph maximum and an FTP reference line. - Added a dedicated workout page alongside the normal page. - Added independent layout and display item settings for each page. - Added automatic switching to the workout page when a workout is detected, and return to the normal page when it ends. - Added display items for current and next step target power, step time remaining, and step distance remaining. - Added handling to preserve workout time remaining and page state while activity recording is paused. - Added full support for receiving and applying settings codes generated by the Configurator. - Placed “Receive Settings Code” and “Receive Result” at the top level of the settings menu, and grouped existing options under “Individual Settings / Advanced.” - Added invalid code rejection, settings recovery after failed