ZULU TIMER keeps today's alarms on one screen and puts a short break in front of each one, so you arrive at the next meeting rested instead of straight from your desk. T-MINUS AT A GLANCE The top of the screen counts down to the next alarm (01:20:35), and the line above it counts down to the start of its break (BRK 01:10) - the moment to stop what you are doing. Below it, your alarms are listed in time order. The next one is marked with a triangle; alarms that have passed fade out. A BREAK BEFORE THE ALARM Each alarm can carry a 5 or 10 minute break in front of it (the cup and the number on its row). By default, when the break starts, the watch gives two short buzzes and the screen shows BREAK; when the alarm itself arrives, three long buzzes and an alarm tone. CHOOSE HOW IT ALERTS YOU Choose vibration only, sound only, both (default) or silent from Alerts in the on-watch menu or Alerts (app open) in the app settings. The same choice applies to breaks and alarms while ZULU TIMER is open. FAST TO SET, ON THE WATCH - SELECT on + ADD. Set each digit with UP / DOWN; SELECT moves through hour tens, hour ones, minute tens, minute ones, then the break. SELECT again to save. BACK returns to the previous digit. - Hold UP or DOWN to change the selected digit quickly; release to stop. Arrows and a bright digit mark what you are changing; the other digits are dimmed. Each digit wraps without carrying into another, and hours stay within 00-23. - A new alarm starts at the next half hour: open it at 13:47 and it offers 14:00. - Repeat any alarm daily or on weekdays (hold UP on its row). - Hold UP on the list for Delete, Clear all, the clock zone, the default break and Alerts. LOCAL OR ZULU The sub-screen shows the time and the date (03 OCT). Choose LCL (local, default) or ZULU (UTC) from the on-watch menu or the app settings; alarms are shown and entered in that zone. When the app is closed, the alarm reaches you as a notification and a prompt to open ZULU TIMER. Sound and vibration for these notifications are managed by the watch; Connect IQ does not let the app select them individually. If an alarm's break and the alarm itself are less than five minutes apart, only the first of the two may reach you while the app is closed. Alarms clear themselves an hour after they pass, so each day starts empty. ZULU TIMER is not affiliated with or endorsed by any military or government organization.

VERSION 1.0.7 - Set each hour and minute digit independently. SELECT moves through the four digits, then the break; BACK returns to the previous digit. - The selected digit stays bright with arrows; other digits are dimmed. Hours stay within 00-23. - Adjusted the time position so all digit arrows remain visible beside the sub-screen. VERSION 1.0.6 - Set hours and minutes separately. SELECT moves from hours to minutes to the break; BACK returns to the previous field. - Hold UP or DOWN to change hours or minutes quickly, and release to stop. - Fixed: the bottom edge of the time could stay bright when dimmed during break selection. VERSION 1.0.5 - Choose vibration only, sound only, both or silent for break reminders and alarms. Hold UP and select Alerts, or use the app settings. - The default is still vibration + sound. This choice applies while ZULU TIMER is open; closed-app notifications remain managed by the watch. VERSION 1.0.4 - Fixed: a repeating alarm switched from Weekdays back to Daily could count down to a day two days ahead (48:00:00) instead of today. - Repeating alarms now keep their local time across daylight-saving changes, and weekdays are counted in local time. VERSION 1.0.3 - A bigger countdown to the next alarm. - Above it, the time left until the break starts (BRK 01:10): the moment to stop what you are doing. - The sub-screen date now reads 03 OCT. VERSION 1.0.2 - Seconds in the countdown, repeating alarms (daily or weekdays), and a new alarm starts at the next clean time for your step. VERSION 1.0.1 - Fixed digits cut off at the bottom and the spacing around the selection frame. VERSION 1.0.0 First release.