This widget allows you to quickly display the current temperature, plus the 24hr min and max, from up to three sources at the same time - Garmin tempe sensors, your watch's built in temperature sensor, or a tempe paired over Bluetooth. Swipe up and down to move between them, or use the glance view to see the first sensor's temperature alongside its 24hr min and max without opening the widget. Your tempes are found automatically. Switch them on, open the widget, and each one gets its own page - two tempes land on two pages without typing any ID into the phone. A sensor that is switched off or out of range simply has no page, so there is nothing to count or configure. Each page shows the reading large, with the tempe's 24hr low and high beneath it and a bar showing where the reading sits between them, how long ago the reading arrived, the tempe's battery, and the sensor's ID so two tempes can be told apart. The label takes a colour from the temperature, blue through red. The page for your watch's own sensor draws the last six hours as a line. Hold the UP button (or press the menu button) for a menu on the watch: a list of which tempe each slot is using, "Forget Tempes" to start the search over, and the battery and white background switches. Each slot is configured separately in the Connect IQ app, with its own name, ID and calibration offset. Sensor ID - leave this at 0 and the widget fills it in with the first tempe it finds that no other slot is using, so the name and offset stay with that tempe from then on. Set it back to 0 to search again. You can also type a tempe's ANT ID yourself. Use -1 for your watch's internal temperature sensor, or -2 for a tempe paired over Bluetooth. Please note the 24hr min and max are reported by the tempe sensor itself, so they are only available on tempe slots. A slot using the watch's internal sensor shows the watch's own six hour history and that window's low and high instead; a tempe paired over Bluetooth shows the current temperature on its own. Some watches don't give access to the internal sensor or to a paired tempe at all; where the watch doesn't provide a reading you will see "--". Sorry, I can't override this. Name - the label shown above the reading, up to 12 characters. Handy if you have one tempe outside and one in the shed. Keep a reading for - how long the widget keeps a value when it isn't getting updated. The reading dims at the halfway point; once the time passes it is cleared and the page goes with it. Tempe C Offset - use this setting to calibrate your tempe. Allows you to enter a positive or negative temperature in Celsius into this field. This will adjust the current temperature and the prior 24 hr Max and Min Temperatures. I added this as I have two tempe devices, which read about 0.5 C different, even though they are positioned next to each other. If you are using fahrenheit, then you will need to convert F to C before entering the value. Show Tempe Battery - this displays an image of the Tempe battery. Once enabled this icon can take up to 5 minutes for the Tempe to publish the battery status. I have tested with various batteries, and I'm not sure how accurate the battery status is on the tempe. I seem to get a status of BATT_STATUS_OK = 3, irrespective of whether the battery is new or old. White Background - switches the display to dark text on a white background, including the glance view. Settings take effect straight away. Changing a name, offset or ID applies while the widget is open, without closing and reopening it. Debug - if you set this to true, sensor and channel events are written to the log. The source code is on GitHub at https://github.com/shane-oconnor/TempeWidget - issues and suggestions are welcome there. Based on the TempX widget, with credit to ekutter, thanks for sharing the code base. Tested as working on fēnix 9 Pro 51mm and 955 Solar, other testing performed on the Connect IQ simulator.

1.1.1 glance min/max - The glance now shows the watch sensor's six hour low and high when no tempe is present, instead of "--" in the Min and Max columns. The full view already showed them 1.1.0 auto Tempe - Tempes are found automatically. One scanning channel hears every tempe in range and gives each its own page, so two tempes no longer race for the same slot. The ID a slot settles on is written into its setting so the name and offset stay with that tempe - The "Number of Tempe" setting is gone. A sensor has a page while it has a reading; one that is off or out of range has none - The full view is redrawn: the reading is large, in a vector font on watches that have one, with the 24hr low and high beneath it and a bar showing where the reading sits between them. The label is coloured by temperature - Shows how long ago each reading arrived, as asked for in the reviews - Shows the sensor's ID under its label, so two tempes can be told apart - The watch's own sensor page draws the last six hours as a line, with that window's low and high - A menu on the watch (hold UP or press the menu button): which tempe each slot is using, Forget Tempes to search again, and the battery and white background switches - The Connect IQ settings are grouped, the timeout is a list of minutes, and the ID codes are explained under the setting instead of in its title 1.0.0 fēnix 8/9, Venu 3/4, Instinct 3 and more - The "Number of Tempe" setting now works. It has been in the settings menu for years but nothing read it, so all three slots were always active. Pick 1, 2 or 3 and the rest are hidden and no longer searched for - Settings now apply while the widget is open. Changing a name, offset, ID or the number of slots no longer needs the widget closed and reopened - The glance view now labels what it is showing - the first sensor's temperature with its 24hr min and max beside it - instead of an unlabelled row of figures - The glance view now scales to the watch screen and follows the White Background setting, instead of being fixed to one size and always dark - A reading more than halfway to its timeout is now drawn dimmed, so a sensor that has gone quiet is visible before the value disappears - Fixed sub-zero temperatures reading slightly too warm. Below freezing the current reading was out by 0.01 C and the 24hr min and max by 0.1 C - Fixed a crash every few seconds on watches with no stored temperature history, cached readings timed against a clock that resets on restart, the offset showing "--", and the battery icon ignoring White Background - A critical tempe battery level is now flagged, not just a low one - Rebuilt the full screen layout so it scales to the watch screen instead of being fixed to 260x260, which should fix the Forerunner 965 and Instinct 2S - Sharper launcher icons, debug logging only in Debug Mode, and far fewer storage writes - Source code published at https://github.com/shane-oconnor/TempeWidget After updating, temperatures may show "--" once on the first launch while the old cache is cleared. Readings come back on the next sensor update. 0.68 Added Garmin Epix models 0.67 Changed Offset max from 5 to 25 0.66 Added Fenix 7 Pro models 0.65 Fixed white background bug. 0.64 Added Temperature offset variable to settings. 0.63 Added support for round sub screens on Instinct Models 0.62 Swipe up and down directions added for scrolling between screens 0.6 Update to allow up to 3 tempe to be connected or 2 tempe and 1 internal temperature. 0.5 Added Battery Status Icon 0.41 Device List Updated 0.4 Additional devices attached 0.3 Additional devices attached 0.2 Fixed bug - 24Min and 24Max value clear after the timeout period now 0.1 Initial Release